logo
Trang chủ
Các sản phẩm
Về chúng tôi
Tham quan nhà máy
Kiểm soát chất lượng
Liên hệ chúng tôi
Yêu cầu báo giá
Tin tức
TOGETHER HTL LTD
Nhà Tin tức

Helicoid vs Sectional Screw Flighting: Which One for Abrasive Materials?

TẬP ĐOÀN HTL LTD là một công ty rất tốt, tôi rất sẵn lòng hợp tác với quý công ty, an toàn, hiệu quả, chuyên nghiệp, trung thực, vui vẻ! Cảm ơn quý công ty đã cung cấp cho tôi dịch vụ và sản phẩm ổn định. -----EUROPAT

—— EUROPT CÔNG NGHIỆP

Tôi trò chuyện trực tuyến bây giờ
Công ty Tin tức
Helicoid vs Sectional Screw Flighting: Which One for Abrasive Materials?
tin tức mới nhất của công ty về Helicoid vs Sectional Screw Flighting: Which One for Abrasive Materials?

For abrasive materials, sectional flighting is generally the better engineering choice. The reason is physical: cold rolling draws the outer edge thinner, while sectional pressing or machining preserves full thickness at the rim. Abrasion attacks the rim first. Sectional also opens the door to Hardox, AR plate and manganese grades that continuous rolling cannot handle economically.

Why Edge Thickness Decides Wear Life

Helicoid flighting is made from strip passed through cone-shaped rolls. The outer edge is compressed during forming, so the finished helix is thick at the root and thin at the periphery—the outer edge can end up roughly half the inner-edge thickness. In light service this saves weight and cost. In abrasive service it removes the wear reserve exactly where the blade contacts the trough and the bulk material.

Sectional flights are cut from plate, split, pressed into single turns and welded into a helix. Thickness is uniform from inner edge to outer edge. A sectional flight made from 12 mm plate has 12 mm at the rim; a cold-rolled helicoid from similar strip stock does not.

Work Hardening Versus Through-Thickness Reserve

Cold rolling does harden the helicoid surface, improving resistance to moderate abrasion. That is why heavy-duty helicoid can serve limestone, cement and fertilizer reasonably well. But work hardening is a surface effect. Once abrasive wear penetrates the hardened skin, the thinner substrate offers little remaining reserve. Sectional flights can be specified in Hardox, AR plate or manganese steel, where wear resistance is a property of the plate rather than a thin surface layer—a decisive advantage in alumina, fly ash, glass cullet and mineral concentrates.

Replaceability and Downtime

A continuous helicoid is difficult to section-replace. A sectional screw can be built with bolted or segmented flights, allowing a worn 1–1.5 m section to be changed without removing the shaft or disturbing adjacent turns. In abrasive plants where downtime cost dominates the maintenance budget, this modularity often outweighs the lower purchase price of helicoid.

Selection Rule

Use sectional when abrasion is severe, thickness or diameter exceeds standard helicoid rolling limits, wear-resistant plate is required, or replaceable segments are valued. Use helicoid when abrasion is moderate, the size is standard CEMA, and first cost is the main driver.

Contact: Lucy Chai | lucychai0315@gmail.com | www.refinerdisc.com | WhatsApp: +86 15373883537

#ScrewFlight #SpiralBlade #MetalForming #HUATAO #auger #screwconveyor #feedmixer #AbrasiveWear #Hardox

Pub Thời gian : 2026-11-17 17:15:15 >> danh mục tin tức
Chi tiết liên lạc
TOGETHER HTL LTD

Người liên hệ: Mr. Maple

Tel: +86 17778255675

Fax: 86--311-80690567

Gửi yêu cầu thông tin của bạn trực tiếp cho chúng tôi (0 / 3000)